Disclaimer: this is not an original idea by me. The original is here: http://www.hobbycraft.co.uk/Pages/Ideas/Idea.aspx?id=1353
 |
| Finished Card |
So this is the first of the DIY projects I intend to throw up on this blog from time to time. Little 'how to do's, rather than my usual random commentary, which never quite manages to talk about the card the post is about. I'd had my eye on the Hobbycraft project I've linked to for a while now, but a few things put me off: the instructions, the two hours suggested work time and the fact it was classified as 'advanced.' Admittedly, despite my love of origami, I've never liked the instructions and always sought out 'how to' movies to make things, so this may not be Hobbycraft's fault, but as I blame them for most things I will certainly blame this on them.
Anyway, they were completely wrong, so that was a relief:
- This is not 'advanced'. It could only ever be considered advanced if folding the card was the intermediate stage, and staring at it blankly was the beginner version. I'd rate it intermediate, but probably a low intermediate.
- Everything together - getting everything out for it, cutting stuff out, the origami, putting it together, embellishing - it took me less than an hour.
DIY TIME:
You will need:
A blank card.
At least four patterned pieces of paper.
Glue
Ruler
Extras: pens, embellishments.
Step One:
Find four patterned (or not so, I tend to think it looks better with some kind of decoration) pieces of paper. They do not need to be big, you'll be cutting them down quite a bit as it is.
First thought: how big is your blank card?
I didn't obey Hobbycraft and used an A6 card rather than folding an A4 sheet. You can see from my finished card that the tree sticks out over the side. So if you are using an A4 sheet then Hobbycraft's sizes should be fine (12cm, 10cm, 8cm, 6cm), if you are using something smaller I would recommend using 10cm, 8cm, 6cm and 4cm. At the bottom of the page you can see an alternative card I made with sizes 8cm, 6cm, 4cm and 2cm. I wouldn't recommend this if you're doing this for the first time, as the 2cm 'branch' was a little fiddly!
So choose your sizes and cut down your paper so you have one square of each. You then need to fold each square in half horizontally and vertically as well as across both diagonals, until you have a 'star' of folds across your paper, as pictured. If you've ever made a fortune teller, (or practically anything in origami) it's the same process.
Step Two:
The next (tiny) section is easy too: just fold back down your horizontal fold so the pattern is on top. Advanced Hobbycraft? Ha!
Step Three:
The next part I've made a little video for. It's not complicated, but it's far easier to watch than describe. This is the part where you create the triangle.
Step Four:
So you have a triangle. It's starting to feel like origami now, isn't it? Well look more closely, you technically have two triangles attached by a fold. Now to finish off a branch of your Christmas tree, all you need to do is grab the front triangle and fold it to make a diamond. To do this you simply have to match the diagonal line of your triangle (the hypotenuse of the right angled triangle, for you mathematical types.) to the straight line of the central fold and sharply crease the new fold you are making.
Now you just need to do this for the other three pieces of paper you cut out. Yes, that really is the complicated part of the design.
Step Five:
So you'll end up with something like I have pictured to the left. To make the Christmas tree you just have to slide them on top of each other, in size order. I found they secured easily enough with just a bit of glue spread at the top of each triangle.
So you've made your Christmas tree, well done! Now you just have to decorate it - add a pot and a trunk for it if you like, embellish them, maybe add some layers of paper for it stand on or a Christmas message. You can see how I chose to in the one I've made for this walkthrough at the top of the page. I also made an alternative one, which is pictured below.